First step on the Windows machine – download PuTTY.exe from This is the communications tool between your PC and the Pi. Since I’m in a Windows environment, I’ll address that.Ģ. The Pi can be accessed over your network from another computer. Here is a rundown of what you need to do in order to get the picture frame to always start up with picture slide show:ġ. If you want to change it, just go back to the little PuTTY program and change it.īecause I already had most of the items I needed for this project sitting around, the final cost for this project was under $30.Īs usual, working with anything Linux is an exercise in trial and error, Googleing, renewing old text file skills and dumb luck. We always download our pictures to the Synology NAS as permanent, backed up storage and now we can actually see all the pictures we’ve been taking! Because Kodi can read all the directories under a directory, you just give it the highest level directory you want and everything gets displayed (no matter how deep of a directly structure you have). Because of the size of the display, you might find that it’s distracting while watching TV if it’s in your line of sight… you keep looking at the display every time it changes pictures!Īll in all, it’s been great.Because it is wireless, keep in mind the location may affect the wifi reception, which in turn will affect the speed of picture changes and video playback.So now that we have had it going for awhile, here are some things to consider: At least for time being, we decided to just keep it on a corner table as it is easy to view from there. We toyed around with where to put this thing. Now is a good time to totally clean the inside of the frame, glass and matte. I put my markings on the back of my matte and made a number runs for each cut, getting deeper each time. Transfer all of these measurements to the matte and CAREFULLY cut out the opening.The edge of the monitor to the inside of the frame was 1”, the sides of the metal monitor frame was about 7/16”… I figured 1-1/2” for each side. For mine, the top was snug up against the frame the bottom had a slat between the monitor and frame – The top was just over ½” (round up to 5/8”) and the bottom was right at ¾” (round up to 7/8”). Measure the top and bottom of the display to the edge of the frame.Make note of measurements: I had 15/16” to the edge of the monitor.For me, the monitor was only movable from side to side, so it was a simple matter of making sure each side had the same distance from the side of the frame. are considered in your final mounting position. Position the monitor in the frame where you want the final mounting to be.If you make the matte opening too large, you will see the metal frame of the monitor. It’s better to make the matte opening smaller than desired. The next cuts are harder because you are cutting the opening for display – determine the distances between the inside of the shadow box frame and outside edges of the display. Make those cuts and check the matte fit in the frame. Measure the frame opening (without the slats) to get the final outside measurements of the matte.If you’re lucky, you might be able to find a matte that’s precut and fits your project without having to do this part. The key here is to carefully layout your lines and use a fresh, sharp utility blade to cut the matte. Just use the original power cables and live with two wires instead of one. Do not attempt this if you do not understand basic wiring principles/safety. One step involves making a splice and adding an electrical outlet to a 110v AC power cable.Disconnect all devices from power before working on them – unplug everything. Tools – For the most part, basic household hand tools are all that are needed for this project. Misc shims, electrical tape, Hook/Loop fastener, etc.Acer AL1706 computer monitor and power cable.Utilize existing equipment/materials when possible to keep the cost down.Controlled from remote PC – no need to access the frame after it’s hung or whatever.Single power chord – Easy cable management, future proof.Fits in a shadow box – No frame construction, inexpensive.Regular PC monitor – easy to hook up to a Pi.The strength of the box wasn’t a concern because the shadow box will be mounted to the monitor and the monitor will be the heavy part that’s actually hanging on the wall. I also wanted to try to keep cabling to a minimum.Īs far as the actual frame was concerned, I hoped that I could find a shadow box that would work. The goal was to create a decent sized, decorative digital picture frame that could connect with our Synology DiskStation Network Attached Storage (NAS) and access our library of pictures from there. This project uses a Raspberry Pi 2 Model B, wireless USB connector and an old Acer AL1706 monitor.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |